Lenze I/O system 1000 Скачать руководство пользователя страница 516

Страница: 516 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

516

PROFINET communication

9.8

Parameterising the counter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Process alarm

A process alarm causes a call of the OB 40. Within the OB 40 you have the possibility of determining

the logic basic address of the module that has triggered the process alarm via the local word 6.

Further information on the triggering event can be found in the "Local double word 8".
Local double word 8 of OB 40:

Gate counter open/closed:

Bit 0 is set if the HW gate is activated while the SW gate is active. Bit 1

is set if the HW gate is deactivated while the SW gate is active.

Ticker value:

After mains connection, a timer (



s ticker) is started which restarts at 0 after 65535



With every change of the count value, the time value of the timer is stored as 16-bit-



s value

together with the count value in the input area.

0x81 0

Final value

Upper limitation of the counting range

0x00

Start value

Lower limitation of the counting range

0x00

Hysteresis

The hysteresis for instance serves to avoid frequent

switching operations of the output and/or triggering of the

alarm when the count value is within the range of the

comparison value. For the hysteresis you can select a range

between 0 and 255. With the settings 0 and 1 the hysteresis

is switched off.

The hysteresis has an effect on the zero crossing,

comparison, overflow/underflow.

0x00

Pulse

The pulse duration indicates for how long the output is to be

set if the parameterised comparison criterion is reached or

exceeded. The pulse duration can be specified in steps of

2.048 ms between 0 and 522.24 ms. If the pulse duration is =

0, the output is set until the comparison condition is no

longer met.

0x00

Local

byte

Bit 7 ... 0

Bit 0: Hardware gate open

Bit 1: Hardware gate closed

Bit 2: Overflow/underflow/final value

Bit 3: Comparison value reached

Bit 4: Latch value

Bit 7 ... 5: 0 (fixed)

State of the inputs at the time of the alarm

Bit 0: A/pulse

Bit 1: B/direction

Bit 2: Latch

Bit 3: Hardware gate

Bit 4: Reset

Bit 7 ... 5: 0 (fixed)

3/4

Ticker value at the time of the alarm

Data set

Name

Description/value

Lenze

No.

Byte

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды