Lenze I/O system 1000 Скачать руководство пользователя страница 424

Страница: 424 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

424

DeviceNet communication

8.4

Parameterising temperature measurement

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Conversion time

channel 1

You can set the transformer speed as a function of the

interference frequency suppression (see 0x3105/x) for each

channel.

0 (0x00): At 50 Hz: 324.1 ms/channel 16 bits; at 60 Hz: 270.5

ms/channel 16 bits

1 (0x01): at 50 Hz: 164.2 ms/channel 16 bits;

at 60 Hz: 137.2 ms/channel 16 bits

2 (0x02): At 50 Hz: 84.2 ms/channel 16 bits;

at 60 Hz: 70.5 ms/channel 16 bits

3 (0x03): At 50 Hz: 44.1 ms/channel 16 bits;

at 60 Hz: 37.2 ms/channel 16 bits

4 (0x04): At 50 Hz: 24.2 ms/channel 16 bits;

at 60 Hz: 20.5 ms/channel 16 bits

5 (0x05): At 50 Hz: 14.2 ms/channel 16 bits;

at 60 Hz: 12.2 ms/channel 16 bits

6 (0x06): At 50 Hz: 9.2 ms/channel 16 bits;

at 60 Hz: 8.0 ms/channel 16 bits

7 (0x07): At 50 Hz: 6.6 ms/channel 15 bits;

at 60 Hz: 5.9 ms/channel 15 bits

8 (0x08): At 50 Hz: 4.2 ms/channel 13 bits;

at 60 Hz: 3.8 ms/channel 13 bits

0x00

Upper limit value

channel 1

You can define an upper or lower limit value for each

channel. For this you can only specify values from the

nominal range, otherwise you'll receive a parameterisation

error. By specification of 0x7FFF for the upper or 0x8000 for

the lower limit value, the corresponding limit value is

deactivated.

If your measured value is outside a limit value and you have

activated the limit value monitoring, a process alarm is

triggered.

0x7FFF

Lower limit value

channel 1

0x8000

Channel 2

Function channel 2

See channel 1

0x50

Conversion time

channel 2

See channel 1

0x00

Upper limit value

channel 2

See channel 1

0x7FFF

Lower limit value

channel 2

0x8000

Channel 3 (for two-wire conductor connections only)

Function channel 3

See channel 1

0x50

Conversion time

channel 3

See channel 1

0x00

Upper limit value

channel 3

See channel 1

0x7FFF

Lower limit value

channel 3

0x8000

Channel 4 (for two-wire conductor connections only)

Function channel 4

See channel 1

0x50

Conversion time

channel 4

See channel 1

0x00

Position in

string

Name

Description/value

Lenze

No.

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды