manualshive.com logo in svg

Lenze I/O system 1000, Справочное руководство

Поделиться
Скачать
Lenze I/O system 1000 Скачать руководство пользователя страница 311

6

PROFIBUS communication

6.10

Parameterising technology modules

311

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

Option 14, cable assignment
0x80 15

Cable assignment

For a connection with minimum reflections and the open 

circuit detection in RS422/485 operation, the cables can be 

pre-assigned via parameters with a defined idle level.

• 0x00:

No pre-assignment of the receive path. This setting is only 

advisable for special drivers that are provided with a bus 

capability.

• 0x01:

Signal R(A) 5V (open-circuit monitoring), signal R(B) 0V

In full duplex operation under RS422, open-circuit 

monitoring is possible.

• 0x02:

Signal R(A) 0V, signal R(B) 5V

This pre-assignment corresponds to the idle state (no 

transmitter active) in half duplex operation under RS485. 

Open-circuit monitoring is not possible.

0x00

Data set

Name

Description/value

Lenze

No.

Byte

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды