Lenze I/O system 1000 Скачать руководство пользователя страница 354

Страница: 354 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

354

EtherCAT communication

7.7

Parameterising the counter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

7.7.2

2 counters 32 bits, 24 V DC - EPM-S601

The following functions can be parameterised:

Counting functions

Description

Continuous counting The counter counts from the loading value to the counting limit, then skips to the opposite

counting limit and continues to count from there.

Counting once

The counter counts once/periodically from the loading value in the specified counting range.

Counting periodically

Signal evaluation

Description

Single rotary

transducer

Connection to "A/pulse" input

Double rotary

transducer
Quadruple rotary

transducer

Connection to input "A/pulse" and "B/direction"

Direction

Pulse at "A/pulse" input and direction at "B/direction" input

Additional functions Description

Main counting

direction

The main counting direction can be parameterised:

None:

The entire counting range is available.

Forwards:

Limitation of the counting range upwards. The counter counts from the

parameterised loading value in the positive direction to the parameterised final value -1 and

then skips to the loading value again with the encoder pulse that is following.

Backwards:

Limitation of the counting range downwards. The counter counts from the

parameterised loading value in the negative direction to the parameterised final value +1

and then skips to the loading value again with the encoder pulse that is following.

Gate function

The gate function serves to start, stop, and interrupt a counting function. In the case of this

counter the internal gate (I-gate) is conform to the software gate (SW gate) which you

control via your user program (status word in the output area).

The following response can be parameterised:

Cancelling gate function:

After closing the gate and opening it again, the counting process

continues from the loading value again.

Interrupting gate function:

After closing the gate and opening it again, the counting process

continues with the last current counter content.

Comparator

You can specify a comparison value which, depending on the count value, activates the

digital output or triggers a process alarm.

Hysteresis

By specification of a hysteresis you can for instance prevent the output from being

permanently switched if the value of an encoder signal fluctuates around the comparison

value.

Process alarm

The activation of a process alarm can be parameterised. A process alarm can be triggered in

the case of the following events:

• Open hardware gate

• Closed hardware gate

• Counter limit overflow

• Counter limit underflow

• Comparison value reached

• Final value reached

• Latch value reached

Diagnosealarm

If the diagnostic alarm is enabled in the parameter setting, it occurs if another process alarm

is triggered for the same event during a process alarm processing.

Diagnostic function

Diagnostic functions are provided by the modules.

Diagnostic

information

The diagnostic information describes the diagnostic contents that can be read out of a

module. Diagnostic information is not automatically sent by the module but must be read

out actively via SDO access.

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды