Lenze I/O system 1000 Скачать руководство пользователя страница 164

Страница: 164 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

164

CANopen communication

5.13

Parameterising technology modules

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

I-3106/x

ZNA (HIGH byte)

Time after request (ZNA)

Waiting time to be complied with until the next transmit

request is executed.

0 ... 65535 [ms] (0x0000 ... 0xFFFF)

0x00

I-3107/x

ZNA (LOW byte)

0x00

Option 4 / 5, character delay time
I-3108/x

Character delay time

(HIGH byte)

Character delay time; the character delay time defines the

max. permissible interval between two received characters

within a frame.

If the character delay time is 0, the module independently

calculates the character delay time on the basis of the baud

rate (approx. the double character time).

0 ... 65535 [ms] (0x0000 ... 0xFFFF)

0x00

I-3109/x

Character delay time

(LOW byte)

0xFA

Option 6, number of receive buffers
I-310A/x

Number of receive

buffers

Defines the number of receive buffers. As long as only one

receive buffer is used and is assigned, no more data can be

received. If up to 250 receive buffers are connected, the

received data can be redirected to a still free receive buffer.

1 ... 255 (0x01 ... 0xFF)

0x01

Option 7 ... 12, reserved
I-310B/x

...

I-3110/x

Reserved

0x00

Option 13, operating mode
I-3111/x

Operating mode

The operating mode determines if the interface is to be

operated half duplex (RS485) or full duplex (RS422).

• 0x00: Half duplex - two-wire operation (RS485)

Half duplex operation means that either transmission or

reception can take place at a time. The data are

transmitted between the communication partners

alternately in both directions.

In case of the half duplex parameter setting under RS485,

no software data flow control is possible.

• 0x01: Full duplex - four-wire operation (RS422)

The data are exchanged simultaneously between the

communication partners; transmission and reception can

take place at the same time. Each communication partner

must simultaneously actuate a receive path.

0x01

Index/subindex

Name

Description/value

Lenze

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды