Lenze I/O system 1000 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 583

Lenze I/O system 1000 Скачать руководство пользователя страница 48

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

48

4

Configuring the I/O system in the »PLC Designer«

4.1

Connecting the I/O system to the Lenze Controller

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

4.1

Connecting the I/O system to the Lenze Controller

• Plug the Controller and modules of the I/O system 1000 onto the fixing rail.
• Always arrange the modules from left to right starting with the Controller directly followed by

a power supply module EPM-S701 to the right or an I/O bus coupler module.

• The modules must always be installed directly next to each other.
• Free slots between the modules are not permissible because otherwise the backplane bus

would be interrupted.

• The side contacts of the last module always must be covered with the supplied contact cover.

Otherwise, the modules may be damaged by short circuit or static discharge.

[4-1]

Example:

Interfaces on the Controller 3231 C



Mounting instructions of the I/O system and the Controller

Here you will find detailed information on how to install the devices.
Observe the safety instructions.



Controller reference manual - Parameterising and programming

Detailed information on the Lenze Controllers is provided here.

32xxC_009

A

Ethernet interface "LAN 1a"

B

Ethernet interface "LAN 1b"

C

EtherCAT interface

G

Slot for optional communication card (MC-Card)

H

Contacts for backplane bus

«
...
46
47
48
49
50
...
»

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды