Lenze I/O system 1000 Скачать руководство пользователя страница 314

Страница: 314 / 583

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

314

PROFIBUS communication

6.10

Parameterising technology modules

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

0x80 14

Operating mode

The operating mode determines if the interface is to be

operated half duplex (RS485) or full duplex (RS422).

• 0x00: Half duplex - two-wire operation (RS485)

Half duplex operation means that either transmission or

reception can take place at a time. The data are

transmitted between the communication partners

alternately in both directions.

In case of the half duplex parametersetting under RS485,

no software data flow control is possible.

• 0x01: Full duplex - four-wire operation (RS422)

The data are exchanged simultaneously between the

communication partners; transmission and reception can

take place at the same time. Each communication partner

must simultaneously actuate a receive path.

0x01

Option 14, cable assignment
0x80 15

Cable assignment

For a connection with minimum reflections and the open

circuit detection in RS422/485 operation, the cables can be

pre-assigned via parameters with a defined idle level.

• 0x00:

No pre-assignment of the receive path. This setting is only

advisable for special drivers that are provided with a bus

capability.

• 0x01:

Signal R(A) 5V (open-circuit monitoring), signal R(B) 0V

In full duplex operation under RS422, open-circuit

monitoring is possible.

• 0x02:

Signal R(A) 0V, signal R(B) 5V

This pre-assignment corresponds to the idle state (no

transmitter active) in half duplex operation under RS485.

Open-circuit monitoring is not possible.

0x00

Data set

Name

Description/value

Lenze

No.

Byte

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды