Lenze I/O system 1000 Скачать руководство пользователя страница 221

Страница: 221 / 583

PROFIBUS communication

6.3

Communication

221

Lenze · I/O system 1000 · Reference Manual · DMS 5.0 EN · 09/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.3.3.1

Services for the acyclic parameter data transfer

Data transfer between DPM 1 and slaves

The connection is established by DPM 1 via the MS1 channel. The connection to the slave can only

be established by the master that has parameterised and configured the slave.

Data transfer between DPM 2 and slaves

The connection is established by DPM 2 via the MS1 channel using the "Initiate" service. One slave

can maintain several active connections at the same time. The number of connections is limited

depending on the resources available in the slave.

Service

Description

Read

The master reads a data block from the slave.

Write

The master writes a data block to the slave.

Alarm

The slave transmits an alarm message to the master. The master acknowledges

receipt. To prevent alarm messages from being overwritten, the slave can only

transmit a new alarm message if it has received the acknowledgement.

Alarm_Acknowledge

The master transmits an acknowledgement to the slave, confirming that it has

received an alarm message.

Status

The slave transmits a status message to the master. The master does not

acknowledge receipt.

Service

Description

Initiate / Abort

Establishing or terminating a connection for the acyclic data transfer between

DPM 2 and a slave.

Read

The master reads a data block from the slave.

Write

The master writes a data block to the slave.

Data_Transport

The master writes user-specific data (defined in profiles) to the slave and, if required,

it reads data from the slave in the same cycle.



Note!

For further information on the services and communication with DP-V0 and DP-V1, refer

to standard IEC 61158.

Содержание I/O system 1000








































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды

Lenze I/O system 1000, Справочное руководство

Результаты поиска

Содержание I/O system 1000

Отзывы:

Бренды по названию

Популярные бренды