manualshive.com logo in svg

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3250 M5 Скачать руководство пользователя страница 97

Step 3.

Cable identifiers are printed on the cables that come with the server and optional devices. Use
these identifiers to connect the cables to the correct connectors.

Refer to the “Internal cable routing and connectors” on page 259 for internal cable routing information.

Updating the server configuration

Use this information to update the server configuration.

When you start the server for the first time after you add or remove a device, you might receive a message
that the configuration has changed. The Setup utility starts automatically so that you can save the new
configuration settings.

Some optional devices have device drivers that you must install. For information about installing device
drivers, see the documentation that comes with each device.

If the server has an optional RAID adapter and you have installed or removed a hard disk drive, see the
documentation that comes with the RAID adapter for information about reconfiguring the disk arrays.

For information about configuring the Ethernet controller, see “Configuring the Ethernet controller” on
page 99.

Chapter 2

.

Installing optional devices

83

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды