Lenovo System x3250 M5 Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 740

background image

000000

000000

000000

000000

000000

Figure 101. 2.5-inch hot-swap hard disk drive installation

0000

0000

0000

0000

0000

0000

000

000

000

000

00000000

00000000

00000000

00000000

00000000

Figure 102. 3.5-inch hot-swap hard disk drive installation

c.

Gently push the drive into the bay until the drive stops.

d.

Rotate the tray handle to the closed (locked) position.

e.

Check the hard disk drive status LED to verify that the hard disk drive is operating correctly. If
the yellow hard disk drive status LED of a drive is lit continuously, that drive is faulty and must
be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed.

Note:

If the server is configured for RAID operation using a ServeRAID adapter, you might

have to reconfigure your disk arrays after you install hard disk drives. See the ServeRAID
adapter documentation for additional information about RAID operation and complete
instructions for using the ServeRAID adapter.

Step 4.

If you are installing additional hot-swap hard disk drives, do so now.

Removing a simple-swap hard disk drive

Use this information to remove a simple-swap hard disk drive.

Removing and replacing server components

175

«
...
187
188
189
190
191
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

Бренд: Wyse Страницы: 6

Бренд: TYAN Страницы: 170

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

847620U - Netfinity 3000 - 20U

Бренд: IBM Страницы: 270

SEH InterCon PS54a-G

Бренд: SEH Страницы: 24

Бренд: Sun Microsystems Страницы: 12

Бренд: 3onedata Страницы: 3

Бренд: Advantech Страницы: 140

Бренд: Fujitsu Страницы: 280

Бренд: Artesyn Embedded Technology Страницы: 2

Бренд: Advantech Страницы: 38

Бренд: Edimax Страницы: 14

T19 Hydro Server

Бренд: BITMAIN Страницы: 17

Бренд: Bosanova Страницы: 2

Бренд: Bosanova Страницы: 2

Бренд: A & T Internationale Страницы: 165

OfficeConnect 3C19500

Бренд: 3Com Страницы: 1

T4MFCS Scaleout

Бренд: VVDN Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды