Lenovo System x3250 M5 Скачать руководство пользователя страница 713

Страница: 713 / 740

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-908-001 : IMM I2C Test Failed

IMM Indicates failure in the PCA9557 bus (BUS 7).

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Perform the actions mentioned one at a time and try the test after each action:

1. Turn off the system and disconnect it from power. Wait for 45 seconds. Reconnect it to power.

2. Make sure that DSA and BMC/IMM are at the latest level.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA tape drive test results

The following messages can result when you run the tape drive test.

Test results for the DSA tape drive test

The following messages can result when you run the DSA tape drive test.

•

264-000-000 : Tape Test Passed

Tape Test Passed.

Appendix C. DSA diagnostic test results

699

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды