Lenovo System x3250 M5 Скачать руководство пользователя страница 558

Страница: 558 / 740

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller

Severity

Warning

User Response

Complete the following steps:

Reboot the system.

2. If problem persists, switch to backup UEFI or reflash current UEFI image.

3. (Trained service technician only) Replace system board.

•

W.305800B [W.305800B] DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller

Severity

Warning

User Response

Complete the following steps:

1. No action required – system will reboot at the end of POST.

2. If problem persists, switch to backup UEFI or reflash current UEFI image.

3. (Trained service technician only) Replace system board.

•

W.305800C [W.305800C] DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required

Controller.

Explanation:

DRIVER HEALTH PROTOCOL: Reports 'System Shutdown' Required Controller

Severity

Warning

User Response

Complete the following steps:

Reboot the system.

2. If problem persists, switch to backup UEFI or reflash current UEFI image.

3. (Trained service technician only) Replace system board.

•

W.305800D [W.305800D] DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires

'Reboot'.

Explanation:

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'

Severity

Warning

User Response

Complete the following steps:

1. Reboot the system to reconnect the controller.

2. If problem persists, switch to backup UEFI or reflash current UEFI image.

544

Lenovo System x3250 M5Installation and Service Guide

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Похожие инструкции для System x3250 M5

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Похожие инструкции для System x3250 M5

Бренды по названию

Популярные бренды