Lenovo System x3250 M5 Скачать руководство пользователя страница 573

Страница: 573 / 740

•

405-907-000 : BRCM:TestLEDs Test Failed

A failure was detected while verifying operation of the status LEDs.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Brocade test results

The following messages can result when you run the Brocade test.

Test results for the DSA Brocade test

The following messages can result when you run the DSA Brocade test.

•

218-000-000 : Brocade:MemoryTest Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Appendix C. DSA diagnostic test results

559

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды