Lenovo System x3250 M5 Скачать руководство пользователя страница 316

Страница: 316 / 740

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0035

User Response

Information only; no action is required.

•

40000024-00000000 : Flash of [arg1] from [arg2] failed for user [arg3].

This message is for the use case where a user has not flashed the firmware component from the interface
and IP address due to a failure.

May also be shown as 4000002400000000 or 0x4000002400000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - other

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0036

User Response

Information only; no action is required.

•

40000025-00000000 : The [arg1] on system [arg2] is 75% full.

This message is for the use case where a Management Controller Event Log on a system is 75% full.

May also be shown as 4000002500000000 or 0x4000002500000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Event Log 75% full

SNMP Trap ID

302

Lenovo System x3250 M5Installation and Service Guide

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Похожие инструкции для System x3250 M5

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Похожие инструкции для System x3250 M5

Бренды по названию

Популярные бренды