Lenovo System x3250 M5 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 740

background image

Figure 155. 2.5-inch simple-swap hard disk drive backplate assembly installation

Step 3.

Connect the cables to the RAID adapter or system board (see “Internal cable routing and
connectors” on page 259).

Step 4.

Reconnect the power cable.

Step 5.

Make sure the relevant cables pass through the cable clips.

Step 6.

Reinstall the hard disk drives and filler panels (see “Replacing a simple-swap hard disk drive” on
page 177).

Step 7.

Reinstall the PCI riser-card assembly if applicable (see “Replacing the PCI riser-card assembly” on
page 163).

Step 8.

Reinstall the cover (see “Replacing the cover” on page 158).

What to do next

1. Install the server into the rack enclosure and push the server into the rack until it clicks into place.

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Removing the 3.5-inch hot-swap hard disk drive backplane

Use this information to remove the 3.5-inch hot-swap hard disk drive backplane.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To remove the 3.5-inch hot-swap hard disk drive backplane, complete the following steps:

Step 1.

Remove the cover (see “Removing the cover” on page 157).

Step 2.

Pull the hard disk drives or fillers out of the server slightly to disengage them from the hard disk
drive backplane (see “Removing a hot-swap hard disk drive” on page 172).

228

Lenovo System x3250 M5Installation and Service Guide

«
...
240
241
242
243
244
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

BladeCenter HS23

Бренд: IBM Страницы: 28

Бренд: Hanwha Страницы: 3

Бренд: Patton electronics Страницы: 331

Бренд: Premio Страницы: 3

SpycerNode 2U12

Бренд: R&S Страницы: 136

Бренд: Velvac Страницы: 55

Server 3100 series

Бренд: Digital Equipment Страницы: 71

Бренд: Integra Страницы: 40

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: Simpact Страницы: 76

Sun Fire Netra 1280

Бренд: Sun Microsystems Страницы: 10

Бренд: 3onedata Страницы: 3

6180DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: LevelOne Страницы: 53

Бренд: Alcatel Страницы: 2

AirPlus G DP-G301

Бренд: D-Link Страницы: 18

Бренд: Viavi Страницы: 12

Бренд: Axis Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды