Lenovo System x3250 M5 Скачать руководство пользователя страница 362

Страница: 362 / 740

164

CIM Information

Prefix:

IMM

ID:

0130

User Response

Information only; no action is required.

•

40000083-00000000 : The new minimum power cap value has returned below the power cap value.

Minimum Power Cap exceeds Power Cap recovered

May also be shown as 4000008300000000 or 0x4000008300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Power

SNMP Trap ID

164

CIM Information

Prefix:

IMM

ID:

0131

User Response

Information only; no action is required.

•

40000084-00000000 : IMM firmware mismatch between nodes [arg1] and [arg2]. Please attempt to

flash the IMM firmware to the same level on all nodes.

A mismatch of IMM firmware has been detected between nodes

May also be shown as 4000008400000000 or 0x4000008400000000

Severity

Error

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

348

Lenovo System x3250 M5Installation and Service Guide

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды