manualshive.com logo in svg

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3250 M5 Скачать руководство пользователя страница 270

0000000

0000000

0000000

0000000

0000000

Figure 184. System board removal

Step 7.

Carefully hold on to the edges of the system board. Avoid touching the connectors on the system
board. Lift and tilt the system board upwards and slightly pull the system board forward (towards
yourself). Then carefully lift and remove the system board from the server.

Note:

When you remove the system board from the server, avoid touching the cable clips on

the side of the chassis and the connectors on the system board. Be careful not to damage any
surrounding components inside the chassis.

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Attention:

Make sure to place the socket cover for the microprocessor socket on the system board before

returning the system board.

Replacing the system board

Use this information to replace the system board.

Notes:

256

Lenovo System x3250 M5Installation and Service Guide

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды