Lenovo System x3250 M5 Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 740

background image

Figure 141. System fan installation

Step 2.

Install the replacement fan in the bracket:

a.

Make sure that the fan cable sits in the channel on the side of the fan.

b.

In the location from which you removed the failed fan, route the fan cable into the fan cable
slot in the fan bracket top.

c.

Insert the fan into the bracket.

d.

Make sure that each of the grey soft tabs on the fan is fully seated in its slot in the fan bracket.

Step 3.

Connect the replacement fan cable to the system board (see “System-board internal connectors”
on page 26 for the locations of the fan cable connectors on the system board).

Step 4.

Reinstall the air baffle if it was removed before (see “Replacing the air baffle” on page 160).

Step 5.

Reinstall the cover (see “Replacing the cover” on page 158).

What to do next

1. Install the server into the rack enclosure and push the server into the rack until it clicks into place.

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Removing the system battery

Use this information to remove the system battery.

The following notes describe information that you must consider when replacing the battery.

• Lenovo has designed this product with your safety in mind. The lithium battery must be handled correctly

to avoid possible danger. If you replace the battery, you must adhere to the following instructions.

Note:

In the U. S., call 1-800-IBM-4333 for information about battery disposal.

Removing and replacing server components

211

«
...
223
224
225
226
227
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

Бренд: Gateway Страницы: 26

Бренд: Xerox Страницы: 8

Бренд: SEH Страницы: 20

x3800 - System - 8865

Бренд: IBM Страницы: 104

Бренд: Hi-flying Страницы: 29

Бренд: Exsys Страницы: 24

6180DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: McIntosh Страницы: 12

Бренд: McIntosh Страницы: 52

Бренд: BITMAIN Страницы: 10

SuperWorkstation 5049A-TR

Бренд: Supermicro Страницы: 189

SuperStorageServer SSG-6119P-ACR12N4L

Бренд: Supermicro Страницы: 211

Бренд: Rittal Страницы: 40

Бренд: 360 Systems Страницы: 148

PowerEdge C6525

Бренд: Dell EMC Страницы: 99

PowerEdge C4140

Бренд: Dell EMC Страницы: 133

Бренд: NASdeluxe Страницы: 6

Бренд: 3onedata Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды