Lenovo System x3250 M5 Скачать руководство пользователя страница 695

Страница: 695 / 740

Test results for the DSA optical drive test

The following messages can result when you run the DSA optical drive test.

•

215-000-000 : Optical Drive Test Passed

Optical Drive Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-801-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Unable to communicate with driver.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the DSA Diagnostic code is at the latest level.

2. Run the test again.

3. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

4. Run the test again.

5. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

6. Run the test again.

Related links

–

IBM Support website

Appendix C. DSA diagnostic test results

681

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды

Lenovo System x3250 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3250 M5

Отзывы:

Бренды по названию

Популярные бренды