Lenovo System x3250 M5 Скачать руководство пользователя страница 437 | Manualshive

Страница: 437 / 740

background image

Automatically notify support

No

Alert Category

Critical - Other

SNMP Trap ID

50

CIM Information

Prefix:

PLAT

ID:

0232

User Response

1.

Check the PCI LED.

2. Reseat the affected adapters and riser cards.

3. Update the server firmware (UEFI and IMM) and adapter firmware. Important: Some cluster

solutions require specific code levels or coordinated code updates. If the device is part of a
cluster solution, verify that the latest level of code is supported for the cluster solution before
you update the code.

4.

Remove both adapters.

5.

Replace the PCIe adapters.

6.

Replace the riser card.

•

806f050c-2001ffff : Memory Logging Limit Reached for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 1)

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Reached.

May also be shown as 806f050c2001ffff or 0x806f050c2001ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Warning - Memory

SNMP Trap ID

43

CIM Information

Prefix:

PLAT

ID:

0144

User Response

1. Check the IBM support website for an applicable retain tip or firmware update that applies

to this memory error.

Appendix A. Integrated Management Module II (IMM2) error messages

423

«
...
435
436
437
438
439
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

NPort P5250A Series

Бренд: Moxa Technologies Страницы: 2

Bull Escala E5-700

Бренд: IBM Страницы: 116

FusionServer G5500 V6

Бренд: xFusion Digital Technologies Страницы: 100

Бренд: Supermicro Страницы: 62

Бренд: Acard Страницы: 43

Бренд: EXAGATE Страницы: 8

PRIMERGY TX2550 M4

Бренд: Fujitsu Страницы: 563

Бренд: Black Box Страницы: 22

Бренд: Black Box Страницы: 28

Бренд: Black Box Страницы: 48

Бренд: Seeed Страницы: 9

Бренд: Planet Страницы: 31

Бренд: I-O Corporation Страницы: 37

Бренд: Plustek Страницы: 2

Бренд: QUANTA Страницы: 52

Бренд: QUANTA Страницы: 177

Бренд: Inspur Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды