Lenovo System x3250 M5 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 740

background image

Figure 54. Adapter installation

Step 7.

Install the PCI riser-card assembly (see “Replacing the PCI riser-card assembly” on page 78).

Attention:

When you install an adapter, make sure that the adapter is correctly seated in the PCI

riser-card assembly and that the PCI riser-card assembly is securely seated in the riser-card
connector on the system board before you turn on the server. An incorrectly seated adapter might
cause damage to the system board, the PCI riser-card assembly, or the adapter.

If you have other devices to install, do so now. Otherwise, go to “Completing the installation” on page 78.

Note:

If the server is configured for RAID operation through an optional ServeRAID adapter, you might have

to reconfigure your disk arrays after you install an adapter. See the ServeRAID documentation on the

Lenovo ServerRAID Support

CD for additional information about RAID operation and complete instructions

for using ServeRAID Manager.

Installing an Lenovo ServeRAID SAS/SATA controller

Use this information to install an Lenovo ServeRAID SAS/SATA controller.

For configuration information, see the ServeRAID SAS/SATA controller documentation at
http://www.lenovo.com/support.

Important:

To ensure that any of your Lenovo ServeRAID SAS/SATA controllers function properly on

UEFI-based servers, make sure that the ServeRAID SAS/SATA controller firmware and supporting device
drivers are updated to the latest version.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are installing an optional device in the server, you need to slide the server out from the rack enclosure,
turn off the server and peripheral devices, and disconnect the power cords and all external cables.

Note:

For brevity, in this documentation the Lenovo ServeRAID SAS/SATA controller is often referred to as

the SAS/SATA adapter or the ServeRAID adapter.

To install an Lenovo ServeRAID SAS/SATA controller, complete the following steps.

Step 1.

Remove the cover (see “Removing the cover” on page 33).

Installing optional devices

61

«
...
73
74
75
76
77
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

N2400 - TaskSmart - 1 GB RAM

Бренд: Compaq Страницы: 372

UltraNEXUS HD Blade

Бренд: Leightronix Страницы: 5

Бренд: Digi Страницы: 118

Бренд: Siemens Страницы: 48

SINUMERIK 840Di sl/840D sl

Бренд: Siemens Страницы: 250

Бренд: Planet Страницы: 68

Бренд: Vlinx Страницы: 47

326m - eServer - 7969

Бренд: IBM Страницы: 82

Бренд: Intel Страницы: 120

Бренд: Lantronix Страницы: 72

Бренд: Acnodes Страницы: 98

Бренд: Planex Страницы: 16

Yingxin NP3020M2

Бренд: Inspur Страницы: 51

Бренд: Gateway Страницы: 135

Бренд: Xblue Networks Страницы: 17

Бренд: Sun Microsystems Страницы: 369

SUPERSERVER 1028TR-T

Бренд: Supermicro Страницы: 144

Бренд: Gigabyte Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды