Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя | Manualshive

Страница: 89 / 171

background image

To be done before spreading

89

Testing the spreading

pattern of the border

spreading plate

Always perform a calibration test first and determine the correct
dosing setting before checking the spreading pattern. Changes to the
dosing setting will also have an influence on the spreading pattern!



See paragraph »Spreading pattern check (tray test)« on page 78.

When using the hydraulic border spreading plate the aim is to obtain
maximum distribution to the edge with minimum loss in the ditch.
This is then why the border spreading plate has to be tested. Do not
perform this test next to the ditch, rather mark a line behind which the
fictive ditch will be.

Operation



Switch the tractor off and remove the key from the ignition and
engage the parking brake of the tractor.



Disconnect the right or left spreading disc by sliding the connector
to the right or to the left. Secure the connector with a lock clip.



Close the dosing unit of the right or left spreading disc.

I

NDICATION

Check that the vanes do not touch the border spreading plate!



Set the spreader in accordance with the spreading chart for the
desired working width and the instructions given in the “One-sided
boundary spreading" chapter

(height of the spreading disc = 75

cm/29.5 in above the troughs)

.



Place 1 trough in the middle of the tractor tracks. The centre of the
driving track must be 7 ft. from the line behind which the fictive ditch
is located.

I

NDICATION

Position the troughs horizontally with a spirit level!

ExactLine

Connector

1

9

«
...
87
88
89
90
91
...
»

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Wassermann Страницы: 24

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Rowlinson Garden Products Страницы: 5

Бренд: Major tech Страницы: 12

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Sweet Sound Electronics Страницы: 6

Бренд: Handicare Страницы: 26

Бренд: Pilz Страницы: 12

Бренд: Foxfury Lighting Solutions Страницы: 17

Бренд: ZOE Страницы: 40

BreadSlicer 208

Бренд: Daub Страницы: 11

Бренд: JEOL Страницы: 4

Бренд: Milwaukee Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды