Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя страница 145

Страница: 145 / 171

Maintenance

145



Attach the rope as per the illustration.



Measure the distance between the inside of the rope and the
opening of the discharge bushing carefully.

If the measured distance is more or less than 109 mm/4.91 in, do the
following:



Loosen the 2 bolts of the actuator plate slightly.



Slide the actuator plate until the distance between the inside of the
rope and the opening of the discharge bushing is 109 mm/4.91 in.



Re-fasten the 2 bolts without sliding the actuator plate again.



Perform the check on the other side as well.



Secure the dashboard by fastening the 3 fixing knobs.

109 mm/4.91 in.

Discharge bushing

Rope

Bolts discharge bushing setting

Actuator plate

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Бренды по названию

Популярные бренды

Kverneland Exacta-TL-GEOSPREAD GS3, Руководство оператора

Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Бренды по названию

Популярные бренды