Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя страница 101

Страница: 101 / 171

Use in the field

101

Last setting check

A checklist is given below, as well as in the jacket of the spreading
chart.



Do this last check to ensure good spreading results.

Are you working with the correct settings from the correct
spreading chart, based on:

•

distribution,

•

similar weight,

•

type of fertilizer,

•

desired working width,

•

desired driving speed?

Did you set the spreader in the correct way?

Did you:

•

set the height over the ground or crops to 75 cm/29.5 in?

•

is the spreader set horizontally to 4º, 8º or 10º?

•

was the correct vane combination mounted?

•

is the correct number of dosing holes opened? (fine application)?

•

is the correct discharge point set?

•

is the correct application rate set?

•

is the correct GEOpoint (Convergence point) set?

•

is the coupling shaft fitted to the correct point on the gearbox?

•

is the ExactLine or border spreading plate in the transport setting
(or working setting)?

•

are the data required entered in the control system?

Did you check the following settings:

Did you:

•

have you checked the control system settings?

•

perform a tray test to check the spreading pattern?

Work in the correct manner:

•

Is the field data selected or input correctly?

•

Is the GEOCONTROL application setting correct?

•

Is the offset setting correct?



Please refer to the software instruction manual.

•

Did you set the correct PTO shaft rpm?

•

Are you driving at the correct driving speed?

•

Did you set the tramlines at the correct distance?

•

Wind speed too high?

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды

Kverneland Exacta-TL-GEOSPREAD GS3, Руководство оператора

Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды