Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя

Страница: 162 / 171

Troubleshooting

162

Machine
makes a noise
while running

Discharge bushing makes contact with
the spreading disc

Please contact your dealer

Spreader put down with filled hopper

Repair the machine.
Set dosing mechanism and discharge
point again

141,
144

Spreading disc hidden/ out of balance

Check the spreading discs for damage
and for the presence of all the vanes

Build-up of fertiliser at the agitator and/or
spreading discs

Remove the fertiliser.
Clean the machine well after each use.

124

Powerful vibra-
tions percepti-
ble

Shut down the PTO shaft immediately!

Attend to the problem to prevent damage

Great imbalance in the spreading discs

Check the vanes and spreading discs

Bent agitator axle or damaged agitator

Replace the agitator axle or the agitator

PTO shaft working angle out of working
reach

Limit the working angle to a maximum of
30º

Alarm on the
control box
screen

The control system cannot perform re-
quested function correctly

Consult meaning and advice in the soft-
ware's instruction manual

The external
system is not
communicat-
ing with the
control box

RS232 plug does not have the correct
connection on the side of the control box
for the signal from the external system

Check and modify the plug pin occupation
on the side of the control box, see user's
manual for control box and external sys-
tem

The control box and external systems are
not communicating with each other in the
same language

Check the control box settings by means
of the external system data, see user's
manual for the control box, tractor, Tellus
and external system

Application rate control by means of an
external signal is not connected

Switch on the external signal reception

External system not switched on or incor-
rectly set

Check external system operation

Spreader does
not appear on
the screen

Control box displays another system

Press the switch key to choose the
spreader display

Spreader ISO plug not connected

Connect the spreader ISO plug

Power supply to the spreader and/or con-
trol box interrupted

Check the electrical cables and fuses

Problem

Possible cause

Solution

Pag

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды

Kverneland Exacta-TL-GEOSPREAD GS3, Руководство оператора

Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды