Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя | Manualshive

Страница: 81 / 171

background image

To be done before spreading

81



Start the tractor again.



Close all the doors and windows in the cabin.



Switch the control box on.



Press the desired application rate in the input field.



Press the OK key to confirm the set application rate.



The working width and the selected driving speed, if the tractor is
equipped with a speedometer, are entered in a similar manner.

It is recommended that an application rate of at least 222 lbs/acre is
entered with the selected driving speed.



Switch the left spreading disc off by pressing the close key in the
main screen. The left dosing unit remains closed while spreading.



Switch the automatic calibration off by pressing the manual/auto
key in the main screen. A hand will begin to flash in the screen on
the right below the spreader.



Engage the PTO shaft and set the RPM of the spreading discs as
given in the relevant spreading chart.



Open the right dosing unit by pressing the start key.



Drive over the first trough and stop only after you have driven at
least 65 ft. past this trough. This is because the spreader
distributes roughly even to the back, front and to the side.



Close the left dosing unit by pressing the stop key.



Empty the trough with a funnel into the graduated tubes and record
the reading in your notebook.

Repeat the above procedure, but disconnect the right spreading disc
and switch the dosing unit of the right spreading disc off. Put the
troughs on the left side of the tractor track.

Drive with the same speed and with the same PTO shaft rpm as
with the first time!

«
...
79
80
81
82
83
...
»

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: SAMCHULLY Страницы: 48

Бренд: Gallagher Страницы: 6

Бренд: HAMAR LASER Страницы: 49

Бренд: PANDROL Страницы: 36

Бренд: Badger Basket Страницы: 7

Бренд: Backyard Discovery Страницы: 53

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: A&D Страницы: 29

Бренд: Vaisala Страницы: 2

Бренд: GE Страницы: 37

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Tarmo Страницы: 4

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды