Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя

Страница: 9 / 171

Safety

Safety labels



SHIELD MISSING

DO NOT OPERATE



ROTATING DRIVELINE

KEEP AWAY!

CONTACT CAN CAUSE DEATH

DO NOT OPERATE WITHOUT-
ALL DRIVELINE, TRACTOR AND

EQUIPMENT SHIELDS IN PLACE.
DRIVELINES SECURELY ATTACHED

AT BOTH ENDS.
DRIVELINE SHIELDS THAT TURN

FREELY ON DRIVELINE.

WARNING

Vertical movement

Risk of injury by lifting or

lowering machine parts.
To avoid death or serious

injury:

Keep out of this area.

WARNING

Vf16661498

AREA OF RISK

Risk of death or injury on

coupling, uncoupling or

operating.
To avoid death or serious

injury:

Keep out of this area.

WARNING

Vf16661500

INADVERTENT OPERATION

Risk of death or injury by

inadvertent operation.
To avoid death or serious

injury:

Switch off the engine.

WARNING

Vf16661510

UNEXPECTED MOVEMENT

Machine parts may still rotate

after engine is switched off.
To avoid fatal or serious injury:

Keep away until parts stop
moving.

WARNING

Vf16661496

RISK OF CRUSHING

Never reach into an area

where parts are still likely to

move.
To avoid fatal or serious injury:

Keep your hands out.

Vf16661512

READ THE MANUAL

The machine must not be

used before reading the

operating manual.
To avoid fatal or serious injury:

Read the manual first.

DANGER

CAUTION

DANGER

Vf16661493

PARTS EJECTED AT SPEED

Parts may become detached and

ejected at speed.
To avoid death or serious injury:

Keep in a safe distance.

Vf16661492

PARTS EJECTED AT SPEED

Parts may become detached

and ejected at speed.
To avoid death or serious

injury:

Keep in a safe distance.

DANGER

A100017974

VERTICAL MOVEMENT

Lifting point with hook tool

Machine handling by:
- Competent personnel
- Suitable device

To avoid death or serious
injury:

WARNING

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды

Kverneland Exacta-TL-GEOSPREAD GS3, Руководство оператора

Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды