Kverneland Exacta-TL-GEOSPREAD GS3 Скачать руководство пользователя страница 56

Страница: 56 / 171

Connecting to the tractor

Coupling the coupling shaft



Check the PTO shaft and the connector for dirt or damage.



Press the safety plate on the connector in.



Slide the connector on the PTO shaft.



Let go of the safety plate.



Check if the safety plate latches by moving the connector.



Attach the check chains to both outer edges of the coupling shaft
protection sleeves.



Mount the other ends of the chains to a fixed point of the tractor,
respectively the machine.

During lifting and lowering of the power lift, the coupling shaft requires
adequate space for:

•

sliding in and out,

•

sufficient overlap between the profiled tubes when driving the
machine in the extreme operating angle of the coupling shaft.

Tip

The maximum operating angle of the coupling shaft is 30

when lifted

and 30

when lowered.The maximum distance allowed between the

PTO shaft of the tractor and the driving axle of the machine is reached
in this position. A greater working angle could damage the coupling
shaft.

WARNING

The coupling shaft provided is too long for most types of
tractors

The coupling shaft must be cut to the correct length before
connecting it to the tractor. A coupling shaft that is too long could
lead to serious damage to the machine and the tractor.



See paragraph »Checking the coupling shaft length« on page
51 and

paragraph »Shortening the coupling shaft« on page 52.

max.30

Содержание Exacta-TL-GEOSPREAD GS3












































































































































































Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды

Kverneland Exacta-TL-GEOSPREAD GS3, Руководство оператора

Результаты поиска

Содержание Exacta-TL-GEOSPREAD GS3

Отзывы:

Похожие инструкции для Exacta-TL-GEOSPREAD GS3

Бренды по названию

Популярные бренды