Kubota L4400 Скачать руководство пользователя

Страница: 221 / 385

4-M1

L4400 , WSM

REAR AXLE

1. STRUCTURE

W1012765

The final gear (9) are final reduction mechanism which further reduces the speed of rotation. The direction of power

transmitted is changed by the differential gear.

The rear axles (2) are the final transmission mechanism which transmit the power from the transmission to the rear

wheels. The rotation speed is reduced by the final gears (9).

The rear axles are the semi-floating type with the ball bearing (1) between the rear axle (2) and rear axle case (3),

which support the rear wheel load besides transmitting power to the rear wheel. The rear axles also support the weight
of the tractor.

(1) Ball Bearing
(2) Rear Axle
(3) Rear Axle

(4) Differential Gear Shaft
(5) Brake Case
(6) Brake Disc

(7) Ring Gear
(8) Differential Pinion
(9)Final Gear

(10) Differential Lock Shifter

(11) Differential Case

(12) Differential Side Gear

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды