Kubota L4400 Скачать руководство пользователя

Страница: 171 / 385

2-S27

L4400 , WSM

CLUTCH

Flatness of PTO Piston and PTO Steel Plate

1. Place the part on a surface plate.
2. Check it unable to insert a feeler gauge (allowable limit size)

underneath it at least four points.

If the gauge can be inserted, replace it.

Piston Return Spring Free Length

1. Measure the free length of spring with vernier calipers.
2. If the measurement is less than the allowable limit, replace it.

W1033828

Thickness of Seal Ring

1. Measure the thickness of seal rings (1) with an outside

micrometer.

2. If the measurement is less than the allowable limit, replace it.

Flatness of PTO piston

Allowable limit

0.15 mm
0.006 in.

Flatness of PTO steel
plate

Allowable limit

0.30 mm
0.012 in.

PTO return spring free
length

Factory spec.

40.5 mm
1.59 in.

Allowable limit

37.5 mm
1.48 in.

PTO brake spring free
length

Factory spec.

20.3 mm
0.38 in.

Allowable limit

18.0 mm
0.71 in.

Thickness of seal ring

Factory spec.

2.45 to 2.50 mm
0.096 to 0.098 in.

Allowable limit

2.0 mm
0.079 in.

(1) Seal Ring

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды