Kubota L4400 Скачать руководство пользователя

Страница: 303 / 385

7-S15

L4400 , WSM

STEERING

[3] SERVICING

(1) Hydraulic Pump (Power Steering

Housing Bore (Depth of Scratch)

1. Check for the scratch on the interior surface of the housing

caused by the gear.

2. If the scratch reaches more than half the area of the interior

surface of the housing, replace at pump assembly.

3. Measure the housing I.D. where the interior surface is not

scratched, and measure the housing I.D. where the interior
surface is scratched.

4. If the values obtained in the two determinations differ by more

than the allowable limit, replace the hydraulic pump as a unit.

(Reference)

• Use a cylinder gauge to measure the housing I.D.

W1014451

Cliarance between Bushing and Gear Shaft

1. Measure the gear shaft O.D. with and outside micrometer.
2. Measure the bushing I.D. with and inside micrometer or cylinder

gauge, and calculate the clearance.

3. If the clearance exceeds the allowable limit, replace the gear

shaft and the bushings as a unit.

W1258963

Side Plate Thickness

1. Measure the side plate thickness with an outside micrometer.
2. If the thickness is less than the allowable limit, replace it.

W1022126

Depth of scratch

Allowable limit

0.09 mm
0.0035 in.

Clearance between
bushing and gear shaft

Factory spec.

0.020 to 0.081 mm
0.0008 to 0.0032 in.

Allowable limit

0.15 mm
0.0059 in.

TighteGear shaft O.D.

Factory spec.

14.970 to 14.980 mm
0.5894 to 0.5898 in.

Bushing I.D.

Factory spec.

15.000 to 15.051 mm
0.5906 to 0.5926 in.

Side plate thickness

Factory spec.

2.48 to 2.50 mm
0.0976 to 0.0984 in.

Allowable limit

2.40 mm
0.0945 in.

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды