Kubota L4400 Скачать руководство пользователя

Страница: 201 / 385

3-S22

L4400 , WSM

TRANSMISSION

Gear Shaft Assemblies

1. Remove shift fork assembly (1), (2) together with counter gear

shaft assembly (3).

2. Remove main gear shaft assembly (4), I-PTO counter gear shaft

assembly (5), I-PTO gear shaft assembly (6), and then PTO gear
shaft (7).

NOTE

■

• To easily remove the gear shaft assembly, tap lightly a tool,

like the one shown in the photo, through small holes (8) from
front inside wall of clutch housing.

W1018805

Rear Propeller Shaft (4WD)

1. Pull out front axle drive shaft (1) from the rear.
(When assembling)

• Install bearing (6), spacer (5), oil seal (4) and internal snap ring

to clutch housing (8)

• Install sleeve (7) to the rear propeller shaft with dimension shown

on the figure, then install the rear propeller shaft from the rear.

• Install sleeve (2) by using rear propeller shaft tool.

W1035817

(1) Shift Fork Assembly (1 - 2)
(2) Shift Fork Assembly (3 - 4)
(3) Counter Gear Shaft Assembly
(4) Main Gear Shaft Assembly

(5) I-PTO Counter Gear Shaft Assembly
(6) I-PTO Gear Shaft Assembly
(7) PTO Gear Shaft
(8) Hole

(1) Rear Propeller Shaft
(2) Sleeve
(3) Internal Snap Ring
(4) Oil Seal
(5) Spacer
(6) Bearing

(7) Sleeve
(8) Clutch Housing

A : To Front Propeller Shaft
L : 538 mm (21.182 in.)

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды