Kubota L4400 Скачать руководство пользователя

Страница: 239 / 385

5-S4

L4400 , WSM

BRAKES

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Adjusting Brake Pedal Free Play

CAUTION

• Stop the engine and remove the key, then chock the wheel

before checking brake pedals.

1. Release the parking brake.
2. Slightly depress the brake pedals and measure free travel (A) at

top of pedal stroke.

3. If the measurement is not within the factory specifications, loosen

the lock nut (1) and turn the turnbuckle (2) to adjust it within the
factory specifications.

IMPORTANT

■

• Keep the free travel in the right and left brake pedals equal.

NOTE

■

• The difference between the right and left pedal free travels

must be less than 5 mm (0.20 in.)

• After checking brake pedal free travel, be sure to engage the

parking brake lock fully and check to see that the brake
pedals are securely locked.

W1014038

Brake pedal free travel
(A)

Factory spec.

15 to 20 mm
0.59 to 0.79 in.

(1) Lock Nut
(2) Turnbuckle

A : Free Play

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды