Kubota L4400 Скачать руководство пользователя

Страница: 215 / 385

3-S36

L4400 , WSM

TRANSMISSION

More than 35 % red lead contact area on the gear tooth

surface.The center of tooth contact at 1/3 of the entire width from the
small end.

W10187470

Replace the adjusting shim (2) with thicker one to move the spiral

bevel pinion shaft backward.

For move the spiral bevel gear rightward, reduce right side shim

(5) and add shim (6) of the same thickness as the right side to left
side.

W10189000

Replace the shim (5) with a thinner one to move the spiral bevel

pinion shaft forward.

For move the spiral bevel gear leftward, reduce left side shim (6)

and add shim (5) of the same thickness as the left side to right side.

Repeat above until the proper tooth contact and backlash are

achieved.

W10189730

Clearance between Differential Case Bore (Differential Case
Cover Bore) and Differential Side Gear Boss

1. Measure the bore I.D. of the differential case and differential case

cover.

2. Measure the differential side gear boss O.D. and calculate the

clearance.

3. If the clearance exceeds the allowable limit, replace them.

W102840310

(A) Proper Contact

(B) Shallow Contact

(C) Heel Contact

(D) Deep Contact

(E) Toe Contact

Clearance between
differential case bore
and differential side gear
boss

Factory spec.

0.050 to 0.151 mm
0.00197 to 0.00594 in.

Allowable limit

0.35 mm
0.0138 in.

Differential case bore
I.D.

Factory spec.

40.500 to 40.550 mm
1.59449 to 1.59646 in.

Differential side gear
boss O.D.

Allowable limit

40.388 to 40.450 mm
1.59008 to 1.59252 in.

Clearance between
differential case cover
bore and differential side
gear boss

Factory spec.

0.050 to 0.151 mm
0.00197 to 0.00594 in.

Allowable limit

0.35 mm
0.0138 in.

Differential case cover
bore I.D.

Factory spec.

40.500 to 40.550 mm
1.59449 to 1.59646 in.

Differential side gear
boss O.D.

Allowable limit

40.388 to 40.450 mm
1.59008 to 1.59252 in.

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды