Kubota L4400 Скачать руководство пользователя

Страница: 45 / 385

G-32

L4400 , WSM

G GENERAL

Replacing Fuel Hose

1. Replace the fuel hoses and clamps.

Refer to “Checking Fuel Line”. (See page G-21.)

W1041643

Replacing Radiator Hose (Water Pipes)

1. Replace the hoses and clamps.

Refer to “Checking Radiator Hose and Hose Clamp”. (See
page G-25.)

W1041698

Replacing Air Hose

1. Replace the air hose and clamps.

Refer to “Checking Intake Air Line”. (See page G-26.)

W1048307

Replacing Power Steering Hose

1. Replace the hoses and clamps. Refer “Checking Power

Steering Line”

W1041752

[13] OTHERS

Bleeding Fuel System

Air must be removed :

1. When the fuel filter or lines are removed.
2. When tank is completely empty.
3. After the tractor has not been used for a long period of time.

CAUTION

• Do not bleed the fuel system when the engine is hot.

Bleeding procedure is as follows :

1. Fill the fuel tank with fuel.
2. Open the air vent cock (1) on the fuel injection pump.
3. Close the air vent cock (1) after 30 seconds.

IMPORTANT

■

• Always close the air vent cock (1) except for bleeding fuel

lines.
Otherwise, Engine runs irregularly or stalls frequently.

W1041811

Draining Clutch Housing Water

NOTE

■

• The tractor is equipped with split pin plug (1) under the

clutch housing.

• After operating in rain, snow or tractor has been washed,

water may get into the clutch housing.

1. Check it by pushing in the split pin (1).
2. If water enters into the clutch housing, remove the plug (1) and

drain the water, then reinstall the plug.

W1041999

(1) Air Vent Plug

(A) CLOSE
(B) OPEN

(1) Split Pin (Plug)

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды