Kubota L4400 Скачать руководство пользователя | Manualshive

Страница: 31 / 385

background image

G-18

L4400 , WSM

G GENERAL

Checking Engine Start System with POC (Operator Presence
Control System)

CAUTION

• Do not allow anyone near the tractor while testing.
• If the tractor does not pass the test do not operate the

tractor.

■

Preparation before testing

1. Sit on operator's seat.
2. Set the parking brake and stop the engine.
3. Shift the main gear shift lever and the range gear shift lever (Lo-

R, H) to "NEUTRAL" position.

4. Shift the PTO lever (PTO clutch control lever) to "OFF" position.

■

Test 1: Switch for the PTO lever

1. Fully depress the clutch pedal.
2. Shift the PTO lever to "ON" position.
3. Turn the key to "START" position.
4. The engine must not crank.
5. If the engine cranks, check or replace the PTO safety switches.

■

Test 2: Switch for the range gear shift lever

1. Fully depress the clutch pedal.
2. Shift the PTO lever to "OFF" position.
3. Shift the range gear shift lever to "Desired" position.
4. Turn the key to "START" position.
5. The engine must not crank.
6. If the engine cranks, check or replace the range gear shift safety

switches.

■

Test 3: Switch for the operator's seat

1. Sit operator’s seat.
2. Fully depress the clutch pedal.
3. Start the engine.
4. Engage the PTO gear shift lever.
5. Get up from the seat.
6. The engine must shut off after approximately 1 second.
7. If the engine does not shut off, check or replace the operator's

seat safety switch

W1031944

(1) Clutch Pedal
(2) PTO Lever
(3) Range Gear Shift Lever
(4) Operator’s Seat

(5) PTO Safety Switches
(6) Range Gear Shift Safety Switches
(7) Operator’s Seat Safety Switches

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

«
...
29
30
31
32
33
...
»

Содержание L4400


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L4400

Бренд: Komatsu Страницы: 6

Бренд: Valtra Страницы: 31

Бренд: Land Pride Страницы: 32

Бренд: Mahindra Страницы: 18

Бренд: Land Pride Страницы: 4

Бренд: GOLDONI Страницы: 99

ARGON CLASSIC 55

Бренд: SAME Страницы: 24

Бренд: Hagie Страницы: 127

Wheel Horse 270HE

Бренд: Toro Страницы: 44

Бренд: Toro Страницы: 44

Бренд: New Holland Страницы: 4

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 184

Workmaster 25 Tier 4B

Бренд: New Holland Страницы: 198

Бренд: New Holland Страницы: 208

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды