Kubota L4400 Скачать руководство пользователя | Manualshive

Страница: 91 / 385

background image

1-S16

L4400 , WSM

ENGINE

(5) Fan Belt

Fan Belt Tension

1. Measure the deflection (A), depressing the belt halfway between

the fan drive pulley and alternator pulley at specified force (98 N,
10 kgf, 22 lbs).

2. If the measurement is not within the factory specifications, loosen

the alternator mounting screws and relocate the alternator to
adjust.

W10356670

Fan Belt Damage and Wear

1. Check the fan belt for damage.
2. If the fan belt is damaged, replace it.
3. Check if the fan belt is worn and sunk in the pulley groove.
4. If the fan belt is nearly worn out and deeply sunk in the pulley

groove, replace it.

W1016443

(6) Radiator

Thermostat Valve Opening Temperature

1. Suspend the thermostat in the water by a string with its end

inserted between the valve and seat.

2. Heating the water gradually, read the temperature when the

valve opens and leaves the string.

3. Continue heating and read the temperature when the valve

opens approx. 6 mm (0.236 in.).

4. If the measurement is not within the factory specifications,

replace the thermostat.

W1035849

Deflection (A)

Factory spec.

7.0 to 9.0 mm
0.28 to 0.35 in.

(A) Deflection

(A) Good

(B) Bad

Thermostat’s valve
opening temperature

Factory spec.

69.5 to 72.5 °C
157.1 to 162.5 °F

Temperature at which
thermostat completely
opens

Factory spec.

85 °C
185 °F

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

«
...
89
90
91
92
93
...
»

Содержание L4400


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L4400

Бренд: LS tractor Страницы: 144

Бренд: Daedong Страницы: 256

Бренд: Ariens Страницы: 44

Бренд: Kioti Страницы: 128

Бренд: MTD Страницы: 28

Бренд: MTD Страницы: 28

Бренд: MTD Страницы: 36

Бренд: New Holland Страницы: 81

Бренд: Dong Feng Страницы: 112

Бренд: PRONAR Страницы: 88

Бренд: Valtra Страницы: 22

Бренд: Yanmar Страницы: 81

Бренд: Husqvarna Страницы: 84

Бренд: Snapper Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды