Kubota L4400 Скачать руководство пользователя

Страница: 92 / 385

1-S17

L4400 , WSM

ENGINE

Radiator Cap Air Leakage

CAUTION

• When removing the radiator cap, wait at least ten minutes

after the engine has stopped and cooled down. Otherwise,
hot water way gush out, scalding nearby people.

1. Set a radiator tester (Code No. 07909-31551) and an adaptor

(BANZAI Code No. RCT-2A-30S) on the radiator cap.

2. Apply the specified pressure 88 kPa (0.9 kgf/cm

, 13 psi), and

measure the time for the pressure to fall to 59 kPa (0.6 kgf/cm

9 psi).

3. If the measurement is less than the factory specification, replace

the radiator cap.

W1054156

Radiator Water Leakage

1. Pour a specified amount of water into the radiator.
2. Set a radiator tester (Code No. 07909-31551) with an adapter

(BANZAI Code No. RCT-2A-30S) and raise the water pressure to
the specified pressure.

3. Check the radiator for water leaks.
4. If any water leaks are detected, replace the radiator or repair with

the radiator cement. If the water leak is excessive, replace the
radiator.

W1016903

Pressure falling time

Factory spec.

More than 10 seconds
for pressure fall from
88 to 59 kPa
(from 0.9 to 0.6 kgf/cm

from 13 to 9 psi)

Radiator water leakage
test pressure

Factory spec.

No leak at 137 kPa
1.4 kgf/cm

20 psi

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды