Kubota L4400 Скачать руководство пользователя

Страница: 210 / 385

3-S31

L4400 , WSM

TRANSMISSION

Differential Pinion Shaft and Differential Pinion

1. Draw out the differential pinion shaft 2 (5), and take out the

differential pinion (3) and differential pinion washer (4).

2. Draw out the differential pinion shaft (1), and take out the

differential pinion (2) and differential pinion washer.

NOTE

■

• Arrange the parts to note their original position.

(When reassembling)

• Check the differential pinions (2) and (3), and pinion shaft (1) and

(5) for excessive wear. If these parts are damaged or
excessively worn, replace the parts they are in mesh with, or they
slide on.

• Apply molybdenum disulfide (Three Bond 1901 or equivalent) to

the inner circumferential surface of the differential pinions.

• Install the parts to their original position.
• Install the differential pinion washers (4), noting its groove

position.

W10741630

[3] SERVICING

(1) Clutch Housing

Checking Bearing

1. Hold the inner race, and push and pull the outer race in all

directions to check for wear and roughness.

2. Apply transmission fluid to the bearing, and hold the inner race.

Then, turn the outer race to check rotation.

3. If there is any defect, replace it.

W1023827

(1) Differential Pinion Shaft
(2) Differential Pinion
(3) Differential Pinion
(4) Differential Pinion Washers
(5) Differential Pinion Shaft 2

(6) Differential Side Gear
(7) Differential Side Gear Washer
(8) Differential Case

A : Fit Groove

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды