Kubota L4400 Скачать руководство пользователя

Страница: 208 / 385

3-S29

L4400 , WSM

TRANSMISSION

PTO Shaft

1. Remove the PTO shaft cover.
2. Remove the bearing case mounting screws, and draw out the

PTO shaft (1) with bearing case (2).

3. Remove the internal snap ring (3).
4. Tap out the PTO shaft (1) to the front.
(When reassembling)

NOTE

■

• If the lock nut (6) was removed, replace it with a new one.

After replacing, be sure to stake it firmly.

• Install the slinger (8) firmly.
• Apply grease to the oil seal (4) and install it, nothing its

direction.

W1021874

Front Wheel Drive Shaft

1. Remove the ball bearing (6).
2. Take out the 24T shifter gear (3), balls and spring (5).

NOTE

■

• Take care not to fly out the balls (4) and spring (5) when take

out the 24T shifter gear (3).

W1029570

Differential Gear Assembly

1. Remove the differential support, noting the number of left shims.
2. Take out the differential gear assembly, noting the number of

right shims.

(When reassembling)

• Check the spiral bevel gear for wear or damage. If it is no longer

serviceable, replace it. Then, also replace the spiral bevel pinion.

• Use same number of shims as before disassembling.

W10247220

Tightening torque

Lock nut

147 to 196 N·m
15 to 20 kgf·m
109 to 145 ft-lbs

Bearing case mounting
screw

23.5 to 27.5 N·m
2.4 to 2.8 kgf·m
17.4 to 20.3 ft-lbs

(1) PTO Shaft
(2) Bearing Case
(3) Internal Snap Ring
(4) Oil Seal

(5) Oil Seal Collar
(6) Lock Nut
(7) O-ring
(8) Slinger

(1) Ball Bearing
(2) Front Wheel Drive Shaft
(3) 24T Shifter Gear

(4) Ball
(5) Spring
(6) Ball Bearing

Tightening torque

Differential support
mounting screw

48.1 to 55.8 N·m
4.9 to 5.7 kgf·m
35.4 to 41.2 ft-lbs

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды