Kubota L4400 Скачать руководство пользователя

Страница: 126 / 385

1-S51

L4400 , WSM

ENGINE

Free Length and Tilt of Valve Spring

1. Measure the free length (A) of valve spring with vernier calipers.

If the measurement is less than the allowable limit, replace it.

2. Put the valve spring on a surface plate, place a square on the

side of the valve spring.

3. Check to see if the entire side is in contact with the square.

Rotate the valve spring and measure the maximum tilt (B).
If the measurement exceeds the allowable limit, replace it.

4. Check the entire surface of the valve spring for scratches.

If there is any defect, replace it.

W11157830

Valve Spring Setting Load

1. Place the valve spring on a tester and compress it to the same

length it is actually compressed in the engine.

2. Read the compression load on the gauge.
3. If the measurement is less than the allowable limit, replace it.

W11177330

Oil Clearance between Rocker Arm and Rocker Arm Shaft

1. Measure the rocker arm shaft O.D. with an outside micrometer.
2. Measure the rocker arm I.D. with an inside micrometer, and then

calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit, replace the rocker

arm and measure the oil clearance again. If it still exceeds the
allowable limit, replace also the rocker arm shaft.

W11199710

Free length (A)

Factory spec.

41.7 to 42.2 mm
1.6417 to 1.6614 in.

Allowable limit

41.2 mm
1.6220 in.

Tilt (B)

Allowable limit

1.0 mm
0.039 in.

(A) Free Length

(B) Tilt

Setting load /
Setting length

Factory spec.

117.6 N / 35.0 mm
12.0 kgf / 35.0 mm
26.4 lbs / 1.3780 in.

Allowable limit

100 N / 35.0 mm
10.2 kgf / 35.0 mm
22.5 lbs / 1.3780 in.

Oil clearance between
rocker arm and rocker
arm shaft

Factory spec.

0.016 to 0.045 mm
0.00063 to 0.00177 in.

Allowable limit

0.10 mm
0.0039 in.

Rocker arm shaft O.D.

Factory spec.

13.973 to 13.984 mm
0.55012 to 0.55055 in.

Rocker arm I.D.

Factory spec.

14.000 to 14.018 mm
0.55118 to 0.55189 in.

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды