Kubota L4400 Скачать руководство пользователя

Страница: 29 / 385

G-16

L4400 , WSM

G GENERAL

Adjusting Clutch Pedal Free Travel

1. Slightly depress the clutch pedal (5) and measure free travel on

top of clutch pedal.

2. If the measurement is not within the factory specifications, loosen

the lock nut (2), remove the cotter pin (3) and the clevis pin (4),
then adjust the length of rod (1) within acceptable limits.

3. Retighten the lock nut, reinstall the clevis pin, the cotter pin and

split the cotter pin.

W1060392

[3] CHECK POINTS OF EVERY 50 HOURS

Greasing

1. Apply a grease to the following position as figures.

NOTE

■

• Apply a small amount of multipurpose grease to the

following points every 50 hours.
If you operated the machine in extremely wet and muddy
conditions, lubricate grease fittings more often.

• When applying a grease to the front axle support, remove

the breather plug and apply a grease until grease overflows
from breather plug. After greasing reinstall the plug.

W1031719

Clutch pedal free travel
on top of clutch pedal

Factory spec.

20 to 30 mm
0.8 to 1.2 in.

(1) Clutch Pedal Rod
(2) Lock Nut
(3) Cotter Pin

(4) Clevis Pin
(5) Clutch Pedal
L : Clutch Pedal Free Travel

(1) Grease Fitting

(Knuckle Shaft RH, LH)

(2) Grease Fitting (Front Axle Support)

(3) Breather Plug

(A) 2WD Type
(B) 4WD Type

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды