Kubota L4400 Скачать руководство пользователя

Страница: 170 / 385

2-S26

L4400 , WSM

CLUTCH

Clutch Case

1. Press the washer (6) lightly by the hand press, using the hand

made jig. (Refer to the figure.)

2. Draw out the piston (4).
(When reassembling)

• Apply enough transmission fluid to seal rings (3) and (8).

W1032846

[4] SERVICING

Clutch Disc Wear

1. Measure the thickness of PTO clutch disc with vernier calipers.
2. If the thickness is less than the allowable limit, replace it.

PTO Steel Plate Wear

1. Measure the thickness of PTO steel plate with vernier calipers.
2. If the thickness is less than the allowable limit, replace it.

W1033498

(1) Clutch Case
(2) Jig
(3) Seal Ring
(4) Piston
(5) Spring

(6) Washer
(7) External Snap Ring
(8) Seal Ring

A : 41 mm (1.6 in.)

Clutch disc wear

Factory spec.

1.70 to 1.90 mm
0.067 to 0.075 in.

Allowable limit

1.55 mm
0.061 in.

Clutch disc wear

Factory spec.

1.15 to 1.25 mm
0.045 to 0.049 in.

Allowable limit

1.10 mm
0.043 in.

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды