Kubota L4400 Скачать руководство пользователя

Страница: 102 / 385

1-S27

L4400 , WSM

ENGINE

Separating Engine from Clutch Housing

1. Place the disassembling stand under the engine and clutch

housing case.

2. Remove the steering support plates connecting steering support

and rear bonnet support.

3. Remove the engine and clutch housing mounting screws and

nuts.

4. Separate the engine and clutch housing.
(When reassembling)

• Apply grease to the spline of clutch shaft.
• Apply liquid gasket (Three Bond 1208D or equivalent) to joint

face of the flywheel housing and clutch housing.

W1044021

Clutch Assembly

1. Insert the clutch center tool.
2. Remove the clutch assembly together with the clutch center tool.
(When reassembling)

• Direct the shorter end of the clutch disc boss toward the flywheel.
• Apply molybdenum disulphide (Three Bond 1901 or equivalent)

to the splines of clutch disc boss.

• Insert the pressure plate, noting the position of straight pins.

IMPORTANT

■

• Be sure to align the center of disc and flywheel by inserting

the clutch tool set.

NOTE

■

• Do not allow grease and oil the clutch disc facing.

W1044164

Tightening torque

Engine and clutch housing
mounting screw and nut
M12, grade 7

77.5 to 90.2 N·m
7.9 to 9.2 kgf·m
57.1 to 66.5 ft-lbs

Engine and clutch housing
mounting stud bolt

39.2 to 49.0 N·m
4.0 to 5.0 kgf·m
28.9 to 36.2 ft-lbs

Tightening torque

Clutch mounting screws

23.5 to 27.5 N·m
2.4 to 2.8 kgf·m
17.4 to 20.3 ft-lbs

(1) Clutch Disc

(2) Pressure Plate Assembly

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды