Kubota L4400 Скачать руководство пользователя | Manualshive

Страница: 97 / 385

background image

1-S22

L4400 , WSM

ENGINE

Draining the Transmission Fluid

1. Place oil pans underneath the transmission case.
2. Remove the drain plugs (1), (2).
3. Drain the transmission fluid.
4. Reinstall the drain plugs (1), (2).
(When refilling)

• Fill up new oil from the oil filling port (3) up to the upper line of the

oil level gauge (4).

• After running the engine for few minutes, stop it and check the oil

level again, add oil to prescribed level, if necessary.

IMPORTANT

■

• Use only multi-grade transmission fluid. Use of other fluides

may damage the transmission or hydraulic system.

• Refer to "LUBRICANTS, FUEL AND COOLANT". (See page

G-8.)

• Never work the tractor immediately after changing the

transmission fluid. Keeping the engine at medium speed for
a few minutes to prevent damage to the transmission.

• Do not mix different brands of oil together.

W1040435

Draining Coolant

CAUTION

• Never remove the radiator cap until coolant temperature is

well below its boiling point. Then loosen cap slightly to the
stop to relieve any excess pressure before removing cap
completely.

1. Stop the engine and let cool down.
2. Loosen the drain plug (1) to drain the coolant.
3. Remove the radiator cap (2) to completely drain the coolant.
4. After all coolant is drained, retighten the drain plug (1).
(When refilling)

• Fill the coolant between the "FULL" and "LOW" marks of

recovery tank.

W1062137

Transmission fluid

Capacity

40 L
10.6 U.S.qts
8.8 Imp.qts

(1) Drain Plug
(2) Drain Plug
(3) Oil Filling Port
(4) Oil Level Gauge

A : Oil level is acceptable within this

range.

Coolant capacity (with recovery tank)

6.0 L
6.9 U.S.qts
5.7 Imp.qts

(1) Drain Plug
(2) Radiator Cap
(3) Recover Tank

(A) FULL
(B) LOW

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

«
...
95
96
97
98
99
...
»

Содержание L4400


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L4400

Бренд: Agrison Страницы: 91

Бренд: DRESSTA Страницы: 177

Бренд: Daedong Страницы: 111

Бренд: GE Страницы: 24

Бренд: Harvest TEC Страницы: 20

Бренд: Harvest TEC Страницы: 20

Бренд: Harvest TEC Страницы: 24

Бренд: Claas Страницы: 31

AXION 810 CMATIC

Бренд: Claas Страницы: 41

Бренд: Claas Страницы: 178

Бренд: BCS Страницы: 66

Бренд: BCS Страницы: 99

Бренд: BCS Страницы: 244

Бренд: ArmaTrac Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды