Kubota L4400 Скачать руководство пользователя

Страница: 112 / 385

1-S37

L4400 , WSM

ENGINE

Fan Drive Pulley

1. Remove the crankshaft nut.
2. Draw out the fan drive pulley (1) with a puller.
(When reassembling)

• Do not tighten the nut excessively, it may damage the oil slinger,

causing oil leakage.

• Apply engine oil to the crankshaft nut. And tighten it.

IMPORTANT

■

• Install the fan drive pulley to the crankshaft, aligning the

marks on them.

W659873210

Gear Case

1. Remove the hour meter gear case.
2. Remove the gear case (2).
3. Remove the O-rings (1).
(When reassembling)

• Apply a liquid gasket (Three Bond 1215 or equivalent) to both

sides of hour meter gear case gasket.

• Check to see if there are four O-rings (1) inside the gear case (2).
• Apply a thin film of engine oil to the oil seal (3), and install it,

noting the lip come off.

• Before installing the gear case gasket, apply a non-drying

adhesive.

Crankshaft Oil Slinger

1. Remove the crankshaft collar (3).
2. Remove the O-ring (2).
3. Detach the crankshaft oil slinger (1).
(When reassembling)

• Insert the crankshaft collar (3) after install the gear case to

cylinder body.

W1081429

Tightening torque

Fan drive pulley mounting
nut

137.3 to 156.9 N·m
14.0 to 16.0 kgf·m
101.3 to 115.7 ft-lbs

(1) Fan Drive Pulley

(1) O-ring
(2) Gear Case

(3) Oil Seal

(1) Crankshaft Oil Slinger
(2) O-ring

(3) Crankshaft Collar

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды