Kubota L4400 Скачать руководство пользователя

Страница: 86 / 385

1-S12

L4400 , WSM

ENGINE

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

(1) Compression Pressure

Compression Pressure

1. Run the engine until it is warmed up.
2. Stop the engine and disconnect the 2P connector from the stop

solenoid in order to inject fuel.

3. Remove the air cleaner, the muffler and all injection nozzle.
4. Set a compression tester (Code No. 07909-30208) with the

adaptor to the nozzle hole.

5. Keep the engine stop lever at “Stop Position”.
6. While cranking the engine with the starter, measure the

compression pressure.

7. Repeat steps 4 through 6 for each cylinder.
8. If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the nozzle hole and
measure the compression pressure again.

9. If the compression pressure is still less than the allowable limit,

check the top clearance, valve cylinder head.

10.If the compression pressure increases after applying oil, check

the cylinder wall and piston rings.

NOTE

■

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for performing this test.
• Variances in cylinder compression values should be under

10 %.

W10178940

Compression pressure

Factory spec.

3.53 to 4.02 MPa
36 to 41 kgf/cm

512 to 583 psi

Allowable limit

2.55 MPa
26 kgf/cm

370 psi

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды