Kubota L4400 Скачать руководство пользователя | Manualshive

Страница: 34 / 385

background image

G-21

L4400 , WSM

G GENERAL

Adjusting Fan Belt Tension

CAUTION

• Be sure to stop the engine before checking fan belt tension.

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between pulleys.
3. If tension is incorrect, loosen the alternator mounting bolts (2),

and using a lever placed between the alternator and the engine
block, pull the alternator out until the deflection of the belt falls
within the factory specifications.

4. Replace fan belt if it is damaged.

W1034711

Checking Fuel Line

CAUTION

• Stop the engine when checking or replacing the fuel line.
• Remember to check the fuel line periodically. The fuel line

is subject to wear and aging, fuel may leak out onto the
running engine, causing a fire.

1. Check to see that all line and hose clamps are tight and not

damaged.

2. If hoses and clamps are found worn or damaged, replace or

repair them at once.

NOTE

■

• If the fuel line is removed, be sure to property bleed the fuel

system.
Refer to "Bleeding Fuel System". (See page G-32.)

W1035367

Adjusting Clutch Pedal Free Play

1. See page G-16.

W1035519

Fan belt tension

Factory spec.

A deflection of between
7 to 9 mm (0.28 to 0.34
in.) when the belt is
pressed in the middle of
the span

(1) Bolt

(A) To Check the Fan Belt Tension
(B) To Tighten the Fan Belt

(1) Fuel Line

(2) Clamp Band

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

«
...
32
33
34
35
36
...
»

Содержание L4400


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L4400

Бренд: Vari Страницы: 44

Бренд: Komatsu Страницы: 6

Бренд: MTD Страницы: 27

Бренд: MTD Страницы: 34

Front Bolster Weight

Бренд: Agriweld Страницы: 10

Бренд: Agriweld Страницы: 24

Бренд: DINGO Страницы: 56

Бренд: Komatsu Страницы: 8

Бренд: Bomford Страницы: 113

Бренд: Craftsman Страницы: 76

Бренд: LS tractor Страницы: 46

Бренд: LS tractor Страницы: 46

Бренд: LS tractor Страницы: 61

Бренд: LS tractor Страницы: 64

Бренд: LS tractor Страницы: 101

Бренд: LS tractor Страницы: 125

Бренд: LS tractor Страницы: 113

Бренд: LS tractor Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды