Kubota L4400 Скачать руководство пользователя

Страница: 213 / 385

3-S34

L4400 , WSM

TRANSMISSION

Free Length of the Shift Fork Spring

1. Measure free length of spring with vernier caliper.
2. If the free length is less than the allowable limit, replace.

W1025587

Spiral Bevel Gear Turning Torque

NOTE

■

• It is necessary to adjust the spiral bevel gear turning torque,

when replacing the differential gears, transmission case or
other relative parts.

1. Assemble the differential gears to transmission case. At this

time, install the some shims (3) to the spiral bevel gear side.

2. Check the turning torque by using turning torque tool (1).

Turning Torque Tool : Weld socket on the brake shaft
(Brake shaft Part No. TA040-26710).

3. Add or reduce the thickness of shims (3) to make the specified

turning torque

4. After getting the specified turning torque, divide the thickness of

shims to left and right side

5. Assemble the transmission case and adjust the backlash and

tooth contact with spiral bevel pinion

W1025673

Free length of the shift
fork spring

Factory spec.

22 mm
0.866 in.

Allowable limit

20 mm
0.787 in.

Turning torque of 37T
spiral bevel gear

Factory spec.

3.92 to 6.37 N·m
0.40 to 0.65 ft-lbs
2.89 to 4.70 Kgf·m

(1) Turning Torque
(2) 37T Spiral Bevel Gear

(3) Adjusting Shim
(4) Differential Support

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

Содержание L4400


































































































































































































































































































































































































Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды

Kubota L4400, Руководство по ремонту

Результаты поиска

Содержание L4400

Отзывы:

Похожие инструкции для L4400

Бренды по названию

Популярные бренды