Kubota L4400 Скачать руководство пользователя | Manualshive

Страница: 294 / 385

background image

7-S6

L4400 , WSM

STEERING

Hydraulic Flow Test (Power Steering)

IMPORTANT

■

• When using a flowmeter which is not specified by KUBOTA,

be sure to follow the instructions for that flowmeter.

• Since the flowmeter has no relief valve, do not close the

flowmeter loading valve completely before testing.

1. Remove the power steering delivery pipe joint bolt and install the

adaptor 52 to the pump discharge port.

2. Connect the hydraulic test hose to the adaptor 52 and flowmeter

inlet port.

3. Connect the other hydraulic test hose to the flowmeter outlet port

and to the transmission fluid filling plug hole.

4. Open the flowmeter loading valve completely. (Turn

counterclockwise.)

5. Start the engine and set the engine speed at 2000 to 2200 min

-

1

(rpm).

6. Slowly close the loading valve to generate pressure approx. 9.8

MPa (100 kgf/cm

2

, 1422 psi). Hold in this condition until oil

temperature reached approx. 40

°

C (104

°

F).

7. Open the loading valve completely.
8. Set the engine speed. (Refer to Condition.)
9. Read and note the pump delivery at no pressure.
10.Slowly close the loading valve to increase to the rated pressure.

As the load is increased, engine speed drops, therefore, reset the
engine speed.

11.Read and note the pump delivery at rated pressure.
12.Open the loading valve completely and stop the engine.
13.If the pump delivery does not reach the allowable limit, check the

pump suction line, oil filter or hydraulic pump.

Condition

• Engine speed : Approx. 2600 min

-1

(rpm)

• Rated pressure :

[2WD] 8.0 to 9.0 MPa
81.4 to 91.4 kgf/cm

2

                 1158 to 1300 psi
[4WD]           10.7 to 11.7 MPa
                 109 to 119 kgf/cm

2

1552 to 1697 psi

• Oil temperature : 40 to 60

°

C (104 to 140

°

F)

W1015559

Hydraulic pump delivery
at no pressure

Factory spec.

Above 17.9 L/min.
4.73 U.S.gals/min.
3.94 Imp.gals/min.

Hydraulic pump delivery
at rated pressure

Factory spec.

Above 17.6 L/min.
4.65 U.S.gals/min.
3.87 Imp.gals/min.

Allowable limit

15.7 L/min.
4.15 U.S.gals/min.
3.45 Imp.gals/min.

KiSC issued 07, 2007 A

Tractor Manuals Scotland - Please Do Not Copy

Tractor Manuals Scotland

«
...
292
293
294
295
296
...
»

Содержание L4400


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L4400

Бренд: SaMASZ Страницы: 29

Бренд: MacDon Страницы: 41

Бренд: Yanmar Страницы: 202

Бренд: Winton Страницы: 40

Бренд: New Holland Страницы: 2

Бренд: New Holland Страницы: 9

Бренд: Mahindra Страницы: 92

Бренд: Challenger Страницы: 51

Wheel Horse 523Dxi

Бренд: Toro Страницы: 60

Бренд: Shibaura Страницы: 74

Бренд: Shibaura Страницы: 126

7000-6 Speed Series

Бренд: Simplicity Страницы: 34

Бренд: Simplicity Страницы: 38

Бренд: Simplicity Страницы: 40

Бренд: Pottinger Страницы: 27

Бренд: LS Страницы: 110

Бренд: Kioti Страницы: 121

Бренд: Kioti Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды